|
 |
|
Dyno
Room |
 |
|
Hot-Shot
Motorworks Dyno
Cell is a State-of-the-Art, Second-to-None
Dynamometer. Hot-Shot Motorworks Dyno is a Engine
Dyno only. With Real-Time Computerized Data
Acquisition (Not Calculated as in Chassis Dyno's).
Hot-Shot Motorworks can monitor these items and many
more:
 | Ignition Timing,
Detonation
|
| Oil Temperature
|
| Oil Pressure
|
| Air/Fuel Ratio (Each
Cylinder is Measured Separately)
|
| Exhaust Gas
Temperature (Each Cylinder is
Measured Separately)
|
| Exhaust Back
Pressure
(Each Cylinder is
Measured Separately)
|
| Cylinder Head
Temperatures
(Each Cylinder is
Measured Separately)
|
| Cylinder
Temperatures
(Each Cylinder is
Measured Separately)
|
| Vacuum/Boost
|
| Crankcase Pressure/Vacuum |
| Volumetric
Efficiencies
|
| Piston Speeds
|
| Piston G's |
| And Many More
Testing Capabilities |
"Click" on Dyno screen
above
left to view full image.
Types of testing
performed at Hot-Shot Motorworks:
| Step Testing (
Steady State ) - This is when we start our testing at
2,000 rpm and step test thru 6,500 rpm and take
samples at every 250 rpm increments at different
throttle positions ( 10% thru 100%TP) to simulate
actual riding conditions. This procedure allows the
engine to stabilize at each rpm step for 5 seconds
and then samples for 5 seconds before proceeding. In
doing this it allows us to monitor the ignition curve
and fuel curve in a stabilized state, not just
passing thru the rpm range quickly as they do on
chassis dyno's.
|
| Sweep Testing - This
allows us to do a quick ( 30-40 seconds ) sweep thru any given
throttle position to evaluate the Torque and
Horsepower Curves after achieving the proper
ignition and fuel curves and settings in a step test.
|
| Reverse Step or
Sweep Test
- Hot-Shot Motorworks use this procedure
to cross check the actual data achieved in testing.
This is when we start our test at 6,500 rpm and Step
or Sweep under load down to 2,000 rpm.
|
| Life Cycle Testing
-
( Durability ) This is what is performed on engines
and products to test it's quality and performance
over an extended period of time ( 10,20,30,40,50-200
hrs) and miles ( 100-50,000 miles).
|
| Accelerated Life
Cycle Testing
- This is when we accelerate the wear
and tear on an engine or components. A load factor
can be computed to simulated up to 500 Road Miles
applied in 1 hr and sustain this for any given period
of time or miles depending on the customer needs.
|
| Clone Testing - This
is when we attach a computer to a motorcycle and
take a trip and monitor all the riding conditions
and then load this information in our dyno computer
and duplicate the exact riding conditions on the
dyno. |
| Reports
- A 5 - 20
page report is produced (Depending on type and
length of test) for each Dyno Test.
|
| These are only a few
of the testing capabilities provided by Hot-Shot
Motorworks State-of-the-Art Dyno Facility.
|
|
|
|
|
|
| Contact Info: |
Address:
555 S. Warpole St.
Upper Sandusky, OH 43351
Phone:
419-294-1997
Fax:
419-294-6997 |
| Quality Parts |
| |
| Specials |
|
"SPECIALS"
Winter
Special!!!
Complete!!!
Engine
Rebuilds
Starting
at
$1,995.00
With Warranty |
|
|
